This section manufacturers recommend full trailer lighting lighthouse: D-SFW6130 model of the company in order to meet the troops, railways, electricity, public security and other enterprises as well as a variety of large construction operations, mining operations, maintenance, repair, incident handling and disaster relief work site of a large area, high brightness lighting needs, especially developed the production of D-SFW6130 full trailer lighting lighthouse in a variety of bad service parts getting off work. First, the full trailer lighting lighthouse Features: 1, the lighting performance: Medallions uses four 1000W energy efficient lamp, lighting, high brightness, large coverage area, lighting, both near and far, lamp life up to 10,000 hours or more, especially for large-scale outdoor task lighting. 2, lifting performance: Lighthouse lift rod made of high strength alloy material is refined, to achieve automatic lift adjustment, the maximum rise height of 6 meters; four lamp can be adjusted up and down separately irradiation angle, so that the light covers the entire job site. 3, Working time: made of imported high power generators, gasoline generators once filled with 9 hours of continuous work; in a place where electricity can also be connected to 220V AC power for long time lighting. 4, Convenient operation: remote control or jog switch two ways to control the movements of the lift rod and stand down, simple operation, safe and reliable; wireless remote control mode can be controlled within a range of 30 meters and a vertical lift rod lift down. 5, Applications: Lighthouse overall use of a variety of high quality alloy material, compact structure, stable performance in a variety of harsh environments and weather conditions to work, wind rating of 8. 6, flexible and convenient: the optimization of structural design, mobile, easy handling, can be easily connected to the trailer to move to any construction, rescue scene. Second, the full trailer lighting lighthouse using method 1, U-shaped mounting bracket body side door open, remove the rear body mounting position on the socket head cap screws. The U-bracket erected in the rear body mounting position, U-shaped bracket located on the left pin. Use a hex screws U-shaped bracket to the rear body. 2, the installation towbar with supports from the top front portion of the vehicle body, and then open the vehicle door. Use a wrench to the body internally fixed L-shaped bracket bolted down, and then out of the L-bracket. Insert the towbar body, bolted inside the body, and then lower the front support legs, adjustable support legs to a suitable height, and then plug in the fixed pin. The interior of the chains out, hanging in the compartment on the bottom of both ends of the hoop, and then drag lever with a chain hook hook; finally out of the supports. 3, install rear compartment rear legs pulled fixed rear legs on both sides of the latch, pull out the support leg to the appropriate location, and then plug in the fixed pin. Move joystick to adjust the rear support leg height so that the wheels off the ground, the body weight on the supporting foot. 4, the installation will lighthouse lighthouse lift rod body carried to the top of the lift rod, placed inside the U-shaped bracket, ensuring the latch inside the U-shaped bracket insert the riser positioning holes. The lift rod six-core cable, four-core cable respectively, through the body on the large and small joints introduce Gülen body, and in accordance with the icon of the cable connected, pay attention to the correspondence between the cable; installation, pay attention Shang Hao packing, tighten the Gülen connectors, ensure the sealing effect. Install two cables, attention should be left outside the body of 15-20CM margin, so when the elevator cable lift rod force. 5, Remove the body mounting rope pulley at the two front pins and lift rod front pulley and alignment. The car body on the winch rope through the pulley position the body at the bottom of the square hole, pull parts from lower groove pulley, and then removed from the front of the lift rod around a pulley, and the pulley mounted on the front end of the lift rod position, rope and then pull back to the upper part of the body at the bottom of the pulley with the pin holes and fix the rope. Taken to ensure that wire rope direction toward the front of the chuck, and to ensure that in the clamped state, can not be loose. Install the front wheels lift rod hole above the pin, to prevent the pulley rope off. 6, install the top cap unscrew the lift rod cap bolts fixed beams; then adjust the four lamp mounting bracket induced horizontal position. The four lamp turn fixed to the beams. Enter the four-head cable access lift rod at the top of the junction box, click the icon requires good line; note four lamp wiring order. Installed junction box cover. Third, the full trailer lighting lighthouse Note 1, adjust the horizontal instrument regulate three feet high, so that the level meter drop to the middle position. 2, to the generator filling fuel, oil filling in accordance with specification requirements turbine fuel, oil. 3, start the generator set generator set in accordance with the instructions start the generator set. Generators started body two side doors must be open in order to facilitate air convection. 4, rising telescopic rod inspection depending on the lighting requirements, adjust the lamp illumination angle; four lamp can be found in the level of 360 °; vertical adjustment range of 180 ° illumination angle. Remove the front part of the fixed pin. Check the top of the lighthouse within the height of 13 meters without any obstacles. Check the wire rope in good condition; Check all fixing pins, bolts secure the lock. 5, open compartments telescopic pole erected operation panel, the operation switch on the control panel to the upright spin up / down bit. Press the red point switch, lift lever to move the upright; when pressed for 3 seconds after the lift bar to start moving the state long, continuous lift rod erected. When the lift lever is fully erect again after pressing the red button to turn off the motor; and then the front of the cabin lift rod fixing pin inserted and fixed. 6, the operation raised telescopic pole switch on the control panel to the "down" position. Press the red point switch, lift lever to move the rise; when pressed for 3 seconds after the lift bar to start moving the state long, continuous lift rod erected. According to the lighting needs to determine the height telescopic pole rises again, press the red button to turn off the motor; lift rod stop rising; lift rod maximum rise height of 10 meters. Lift rod rose bit, it will switch on the operation panel Midseat to prevent misuse. 7, open lamp, for lighting the four flip control panel light switch, light lamps for lighting; lamp start-up time is about 10 minutes; 10 minutes after the lamp has been fully activated. On or off according to the need of any set of lamps. Close lamps start again, you should wait for about 20 minutes, the lamp until completely cooled before they can start again. The top of the control panel is provided with a panel of light switches, when pressing the switch, lighting start, staff can easily operate at night. 8, remote control Lighthouse lift, vertical lift rod down the lighthouse and down, stand down can also be remote controlled, remote control range of 30 meters. Remote control with A, B two keys; wherein "A" key control l / Li, "B" keys to control the drop / fall. With the remote control of the movements of the lift rod. The rotary switch on the control panel set to the "down" position, then move the A key safety; lifter rises; pressing the B button, the lift rod down. With the remote control lift rod stand down. The rotary switch on the control panel set to the "stand down" position, then move the A key safety; lift rod erected; pressing the B button, the lift rod down. 9, turn off lamps after use, you should first turn off the lamps. Open body panel, turn off the four lamps. 10, the operator lowered telescopic pole switch on the control panel to the "down" position. Press and hold the green button for 3 seconds after lift rod normal lowered. When the lift rod down position, press the green button again to turn off the motor. 11, check the lift rod telescopic rod tipped down direction, no human activity. Fixed lift rod fixing pin removed. The operation switch on the control panel to the "stand down" position. Press and hold the green button for 3 seconds after lift rod slow down. When the lift levers into position, press the green button again to turn off the motor. The end of the fixing pin Shanghao body to prevent movement of the sliding riser. 12 Close Close turbine generator sets. Close bodywork two side doors. 13, the vehicle body is connected to the front end of trailer trailer connected to the vehicle body. Collapse three support legs, and a lock pin fixed. Remove the interior of the lamp cable and connected to the lighthouse trailer onto the designated location. Four, full trailer lighting lighthouse in strict accordance with the quality assurance of the product IS9001: 2000 international quality management system standards for quality control to ensure product higher than the national standard, fully meet the design requirements, from 3 years from the date of purchase, the product under normal use any failure by the company free maintenance. Note: This product price is nominal price, other products visible: http://yuandir.cn.gongchang.com/ details, please contact: Mr. Zhang Q2735368669 and telephone 027-84899678 or 15807103802.